DFB400 - 400 瓦DC-DC 轉換器帶隔離, 400瓦DC/DC轉換器 : DFB400

DC-DC Converter- Isolation - Module

400W Isolated Full-Brick Size DC/DC Converter Meet Industry Standard.

• Efficiency up to 90%<
• Fixed Switching Frequency
• Input Under Voltage Protection
• Fully protected (OTP/OVP/OCP)
• Remote On/Off
• Full-Brick Size Meet Industry Standard
• Fully Isolated 1500VDC

Input Voltage Range	24Vin Range: 9~36Vdc ; 48Vin Range: 18~75Vdc
Under voltage Lockout	24Vin power up 8.5V, power down 7.5V 48Vin power up 17V, power down 15V
Input Over Voltage Protection	24Vin Turn Off...42V, Turn On...40V 48Vin Turn Off...83V, Turn On...80V
Input Filter	LC Type
Voltage Accuracy	± 1% max
Transient Response	25% step load change < 500us
External Trim Adj. Range	80-110%
Load Share Accuracy	±10% at 50% to 100% full load
Auxiliary Output Voltage/Current	10±3Vdc/20mA max.
R&N (20MHz bandwidth)	5V ....... 40mV RMS max., 100mV pk-pk max. 12V ..... 60mV RMS max., 120mV pk-pk max. 24V ... 100mV RMS max., 240mV pk-pk max. 28V ... 100mV RMS max., 280mV pk-pk max. 48V ... 120mV RMS max., 480mV pk-pk max.
Temperature Coefficient	± 0.03% / °C max.
Short Circuit Protection	Continuous
Line Regulation	± 0.2% max
Load Regulation	± 0.5% max.
O.V.P. Trip Range, % Vo nom.	115-140%
Current Limit	110%-150% nominal output
Set up time	120ms typ.
Isolation Voltage	Input/Output ... 1500VDC min. Input/Case ...... 1500VDC min. Output/Case .... 1500VDC min.
Isolation Resistance	107 ohm min.
Isolation Capacitance	4000pF Typ.
Switching Frequency	230 KHz Typ.
Operating Case Temperature	-40°C to 100°C
Storage Temperature	-55°C to 115°C
Thermal Shutdown, Case Temp.	110°C Typ.
Humidity	95% RH max. non condensing
MTBF	MIL-HDBK-217F, GB, 25°C, full load ; 340Khrs typ.
Case Material	Aluminum baseplate with plastic case
Dimensions	L4.6xW2.4xH0.50 inches (116.8x61.0x12.7mm)
Weight	220g

Notices：

1. x = blank stands for Remote On/Off Logic Negative
   x = P stands for Remote On/Off Logic Positive
2. Nominal Input Voltage 24, 48VDC.
   Measured at Nominal Input Voltage.
   Measured at 12VDC for 24Vin, 24VDC for 48Vin.
3. The output terminal of 5V Vout models required a minimum capacitor 680uF to maintain specified regulation.
   The output terminal of 12/24/28V Vout models required a minimum capacitor 330uF to maintain specified regulation.
   The output terminal of 48V Vout models required a minimum capacitor 100uF to maintain specified regulation.
4. An external input capacitor 1000uF for 24Vin or 330uF for 48Vin models are recommeded to reduce input ripple voltage.
5. If the remote sense feature is not to be used, the +sense pin should be connectoed to the +Vout pin and the -sense pin should be connected to the -Vout pin.