FPM300 - 200-300 WATT Single Output MEDICAL POWER SUPPLIES

Medical Open Frame

The FPM300 series comprising single and multiple output models for 200-300 watts of continuous output power is specially designed for medical applications. They operate at 90-264 VAC input voltage without the need of a selector strap. All auxiliary outputs are with magnetic amplifier to keep regulation. The units are constructed on a printed circuit board with a U-bracket for mechanical support and heat sinking. A cover-and-fan assembly can be added during manufacturing. FPM300-zyyy-z x = S or Q to denote multiple output ; S for single output, Q for Quad output ; yyy to denote different output rating ; z = U or E to denote different casing type ; U for U-bracket, E for Enclosed.

• EN61000-3-2 class A and D compliant
• Power Factor 0.98 typical
• Overvoltage protection
• Short-circuit protection
• Power Fail Detect (PFD) signal
• 100% burn-in at full rated load
• Remote sense on output #1 and output #2
• Remote inhibit – TTL high to disable output
• Compliant with RoHS requirements

Input voltage	90-264 VAC
Input frequency	47-63 Hz
Input current	4.7 A (rms) for 115 VAC ; 2.3 A (rms) for 230 VAC
Earth leakage current	300 μA max. @ 264 VAC, 63 Hz
Touch current	100 μA max. @ 264 VAC, 63 Hz
Output voltage/current	See rating chart.
Maximum output power	See rating chart.
Ripple and noise	2% peak to peak maximum on 3.3 V & 5.1 V and 1% peak to peak maximum on other voltage outputs
Overvoltage protection	Provided on output #1 only; set at 115-140% of its nominal output voltage
Overcurrent protection	All outputs protected to short circuit conditions
Temperature coefficient	All outputs ±0.04% /℃ maximum
Transient response	Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500 us after a 25% step load change
Fan power	12 V at 350 mA maximum for B version, 12 V at 100 mA maximum for C version
PFD	TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1 ms prior to V1 output dropping 5% below its nominal value. This signal also provides a minimum delay of 100 ms after V1 output is within regulation.
Inhibit	Requires an external TTL high level signal to inhibit outputs for standard models
Operating temperature	0℃ to +70℃
Storage temperature	-40℃ to +85℃
Relative humidity	5% to 95% non-condensing
Derating	Derate from 100% at +50℃, linearly to 50% at +70℃
Cooling	200 /250 /300 watts continuous output power at 35 CFM forced air cooling or 100 /125 /150 watts at convention cooling
Switching frequency	70 KHz ±10 KHz
Power factor	0.98 typical
Efficiency	70% minimum on all models
Hold-up time	12 ms minimum at 110 VAC
Line regulation	±0.2% maximum at full load
Inrush current	30 A @ 115 VAC or 60 A @ 230 VAC, at 25℃ cold start
Withstand voltage	5600 VDC from input to output (2 MOPP) ; 2100 VDC from input to ground (1 MOPP) ; 700 VDC from output to ground(To verify AC strength, get correct test method to avoid power supply damage.)
MTBF	300,000 hours minimum at full load at 25℃ ambient, calculated per MIL-HDBK-217F EMC Performance (EN60601-1-2)
EN55011	Class B conducted, class B radiated
EN61000-3-2	Harmonic distortion, class A and D
EN61000-3-3	Line flicker
EN61000-4-2	ESD, ±15 KV air and ±8 KV contact
EN61000-4-3	Radiated immunity, 10 V/m
EN61000-4-4	Fast transient/burst, ±2 KV
EN61000-4-5	Surge, ±1 KV diff., ±2 KV com
EN61000-4-6	Conducted immunity, 10 Vrms
EN61000-4-8	Magnetic field immunity, 30 A/m
EN61000-4-11	Voltage dip immunity, 30% reduction for 500 ms, 100% reduction for 10 ms